p code oem gps - JNS100

JNS100 marks a new generation of high precision GPS boards in a small size. It is an OEM board based on our new JNScore chip that is able to output raw data and position solution 100 times per second without interpolation. The second processor of the JNScore can be used for user applications.

* Not available through Mighty GPS to US based customers. Various options and prices are available. Contact us for more info.

Features

Tracking Features

50 channel, all-in-view: L1 GPS, WAAS/EGNOS and GLONASS
Low signal tracking (down to 30 dB*Hz)
Fast acquisition and fast re-acquisition
Up to 30 g's of dynamic
Almost unlimited altitude and velocity (for authorized users)
Advanced Multipath Mitigation
High accuracy, low latency velocity measurements

Data Features

Up to 100 Hz update rate for real time position and raw data (code and carrier)
10 cm code phase and 0.1 mm carrier phase precision
RTCM SC104 versions 2.3 Input
NMEA 0183 versions 2.1, 2.2, 2.3 and 3.0 Output
Geoid and Magnetic Variation models
RAIM
Different DATUMs support
Output of grid coordinates

Input/Output

Four high speed (115.2 Kbps) standard RS232 Serial Ports
1 PPS output (TTL) synchronized to GPS, UTC, or GLONASS
Event marker input
2 external LED drivers

Electrical

On-board power supply accepts any unregulated voltage between 6.5 and 40 volts
On-board back up battery saves data for about 10 years
Typical power consumption is 0.8W

Environmental

Operating Temperature -30C to +80C
Storage Temperature -40C to +85C
High shock and vibration resistance

Physical

Dimensions: 88 x 57 x 15 mm
Weight: 48 g
Connectors: 30 pin for digital, MMCX for antenna

Dimensions and layout

Pinout

Pin #	Signal Name	Description	I/O	Comments
1	GND	Digital Ground
2	CTSA	Clear to Send for Serial Port A	I
3	TXDA	Transmitted data for Serial Port A	O
4	RTSA	Request to Send for Serial Port A	O
5	RXDA	Received Data for Serial Port A	I
6	NC	Not Connected
7	GND	Digital Ground
8	CTSB	Clear to Send for Serial Port B	I
9	TXDB	Transmitted data for Serial Port B	O
10	RTSB	Request to Send for Serial Port B	O
11	RXDB	Received Data for Serial Port B	I
12	BOOT	Boot Loader — Factory use only	I	Must be grounded or open
13	PWR_IN	Power Supply	PWR	+6.5 to +40.0 Volt
14	PWR_IN	Power Supply	PWR	+6.5 to +40.0 Volt
15	NC	Not Connected
16	NC	Not Connected
17	EXT_RESET*	External Reset Control	I	Connect to ground to activate
18	1PPS	1 Pulse Per Second	O	V_oh > 2.0V @ 50Ohm, T=3.2mS
19	PWR_GND	Power Ground	PWR
20	PWR_GND	Power Ground	PWR
21	LED_RED	External LED	O	See Note
22	LED_GRN	External LED	O	See Note
23	TXDC	Transmitted data for Serial Port C	O
24	GND	Digital Ground
25	RXDC	Received Data for Serial Port C	I
26	GND	Digital Ground
27	EVENT	Event Marker	I	10kOhm internal pull-up to +3.3V
28	TXDD	Transmitted Data for Serial Port D	O
29	NC	Not Connected
30	RXDD	Received Data for Serial Port D	I

Note: LED_RED and LED_GRN are used to control the STAT LED of the MinPad. The output is a +3.3V driver in series with 100 Ohm resistor for each LED. LEDs should be with common cathode.

RF Connector

J001 is GPS/GLONASS antenna input connector, MMCX. The central pin of this connector is power supply for LNA, 5 VDC.

Note: Specifications are subject to change without notice.