p code gps module - Euro-GDA

The card is exactly half Eurocard size (100 x 80 mm) with standard Eurocard width, connector and pin-out. Password upgradeable from single to dual frequency GPS.

The card is based on our field proven JNSChip. Each card includes on board compact flash for data storage of up to 1024 MB.

* Not available through Mighty GPS to US based customers. Various options and prices are available. Contact us for more info.

Features

Tracking Features

20 channel, all-in-view, L1+L2 GPS and WAAS
Low signal tracking (down to 30 dB*Hz)
Fast acquisition and fast re-acquisition
Common Tracking (high satellites help low satellites)
Up to 30 g's of dynamic
Almost unlimited altitude and velocity (for authorized users)
Advanced Multipath Mitigation

Data Features

Up to 20 Hz update rate for real time position and raw data (code and carrier)
10 cm code phase and 0.1 mm carrier phase precision
RTCM SC104 versions 2.1 and 2.2 Input/Output
NMEA 0183 versions 2.1, 2.2, 2.3 and 3.0 Output
Multiple Base RTCM
Geoid and Magnetic Variation models
RAIM
Different DATUMs support
Output of grid coordinates
CMR and CMR+ support

Input/Output

Four high speed (460.8 Kbps) standard RS232 Serial Ports
1 PPS output (TTL) synchronized to GPS, UTC, or GLONASS
Event Marker Input
4 external LED drivers

Electrical

On-board power supply accepts any unregulated voltage between 8.0 and 40 volts
On-board back up battery saves data for about 10 years
Power consumption:
- Minimum: 1.8W
- Typical: 2.1W
- Maximum: 2.4W

Environmental

Operating Temperature -40°C to +75°C
Storage Temperature -40°C to +75°C

Dimensions and layout

External Connectors

Main Euro connector (J601)

DIN41612, 2 row x 32 pin, Right Angle, Male, MOLEX P/N 53294-0641

Pin #	Signal Name	Description	I/O	Comments
A1	PGND	Power Ground	-
A2	PWR_IN	Power Supply	I	+8.0V to +40.0V to PGND
A3	FREEZE	Boot Loader – Factory Use Only	O	Must be left open
A4	GND	Digital Ground	-
A5	LED2_RED	External LED control	O	See Note 1
A6	LED2_GRN	External LED control	O	See Note 1
A7	GND	Digital Ground	-
A8	NC	No Connect	-
A9	TXDA	Transmitted Data for Serial Port A	O
A10	RXDA	Received Data for Serial Port A	I
A11	TXDC	Transmitted Data for Serial Port C	O
A12	RXDC	Received Data for Serial Port C	I
A13	TXDD	Transmitted Data for Serial Port D	O
A14	RXDD	Received Data for Serial Port D	I
A15	GND	Digital Ground	-
A16	AUX_OUT1	General Purpose Output 1	O	3.3V Logic Level
A17	TXDB	Transmitted Data for Serial Port B	O
A18	RXDB	Received Data for Serial Port B	I
A19	AUX_OUT3	General Purpose Output 3	O	3.3V Logic Level
A20	AUX_OUT5	General Purpose Output 5	O	3.3V Logic Level
A21	BOOT	Boot Loader – Factory Use Only	I	Must be connected to GND or left open
A22	GND	Digital Ground	-
A23	GND	Digital Ground	-
A24	GND	Digital Ground	-
A25	GND	Digital Ground	-
A26	AUX_IN0	General Purpose Input 0	I	Internal Pull-Down 5kOhm
A27	AUX_IN2	General Purpose Input 2	I	Internal Pull-Down 5kOhm
A28	GND	Digital Ground	-
A29	GND	Digital Ground	-
A30	NC	No Connect	-
A31	NC	No Connect	-
A32	ONOFFSW*	External ON/OFF Control for On-Board Power Supply	I	Active LOW input which is equivalent to ON/OFF button of the MinPad. The pin MUST BE CONNECTED TO GND permanently if the board is required to turn on automatically any time external power ia applied to pins A2 and/or B2
B1	PGND	Power Ground	-
B2	PWR_IN	Power Supply	I	+8.0V to +40.0V to PGND
B3	COMMSW*	External COMMAND Control	I	Active LOW input from the FN button of the MinPad. Must be left open if not used
B4	NC	No Connect	-
B5	LED1_RED	External LED control	O	See Note 1
B6	LED1_GRN	External LED control	O	See Note 1
B7	NC	No Connect	-
B8	NC	No Connect	-
B9	CTSA	Clear to Send for Serial Port A	I
B10	RTSA	Request to Send for Serial Port A	O
B11	CTSC	Clear to Send for Serial Port C	I
B12	RTSC	Request to Send for Serial Port C	O
B13	CTSD	Clear to Send for Serial Port D	I
B14	RTSD	Request to Send for Serial Port D	O
B15	AUX_OUT0	General Purpose Output 0	O	3.3V Logic Level
B16	AUX_OUT2	General Purpose Output 2	O	3.3V Logic Level
B17	CTSB	Clear to Send for Serial Port B	I
B18	RTSB	Request to Send for Serial Port B	O
B19	AUX_OUT4	General Purpose Output 4	O	3.3V Logic Level
B20	AUX_OUT6	General Purpose Output 6	O	3.3V Logic Level
B21	AUX_OUT7	General Purpose Output 7	O	3.3V Logic Level
B22	1PPS	1 Pulse per Second	O	V_oh > 2.0V @ 50Ohm, T=3.2mS
B23	NC	No Connect	-
B24	EVENT	Event Marker	I	10kOhm internal pull-up to +3.3V
B25	NC	No Connect	-
B26	AUX_IN1	General Purpose Input 1	I	Internal Pull-Down 5kOhm
B27	AUX_IN3	General Purpose Input 3	I	Internal Pull-Down 5kOhm
B28	RESET_IN*	External Hard Reset Control	I	Active LOW. Must be left open if not used.
B29	NC	No Connect	-
B30	NC	No Connect	-
B31	NC	No Connect	-
B32	GND	Digital Ground	-

Note 1: LED1_RED and LED1_GRN are equivalent to STAT LED of MinPad. LED2_RED and LED2_GRN are equivalent to REC LED of MinPad. The output is +3.3V driver in series with 100 Ohm internal resistor for each LED. LEDs should be with common cathode.

RF Connector

J001 is GPS antenna input connector.
It is MMCX RIGHT ANGLE PCB JACK, THROUGH HOLE, AMPHENOL P/N 908-24100.
The central pin of this connector is power supply for LNA. Nominal antenna voltage is +5.0V.

Note: Specifications are subject to change without notice.